Polyurethane Self Leveling Floor Coating

PRODUCT DESCRIPTION & USE

Is a solvent free, self leveling, two component industrial floor coating. Warehouses, manufacturing plants, laboratories, chemical and pharmaceutical industries, shops and supermarkets, aircraft hangars

KEY FACTORS

• Easy to apply,
• Mechanical resistance is high,
• Have Surface structure which does not allow for the formation of germs,
• Crack envelopment power, 
• Semi-flexible,
• Can be applied to asphalt

 

AVAILABLE IN SIZES

A component: 20 kg, B component: 4 kg tin buckets

 

COLOUR & GLOSS RANGE

Various color options, glossy

 

FLASH POINT

Flash point of this product is 39 degrees Celsius. 

 

VOC CONTENT

Available upon request

 

COMPOSITION (NOMINAL)

Pigment: Lightfast pigment

Binder: Alkyd resin

Solvent: Toluen

 

SOLIDS – SPECIFIC GRAVITY

Volume Solids % 95

Specific Gravity 1.45 kg/L   (@ 20 °C)

   

PHYSICAL CHARACTERISTICS

Pressure resistance         510-560 kg/cm, 

Flexural strength             326 kg/cm²

 

SURFACE PREPARATION

The application surfaces should be cleaned from the dirt, oil, dust and all loosen structured swollen layers, the faults on the surface should be removed.

 

APPLICATION

The surface which will be applied previously must prime with suitable primer materials. While application is made, ground temperature +3 ° C above the Dew point must be attention. Is presented two components ready to use. Main Material (A) component with the hardener (B) component mix as a homogeneous at least 3 minutes. Do not mix by hand or partial mix. Before mixing, precondition both A and B components to a temperature of approximately 15 to 25ºC. Pour the entire contents of Part B into the container of Part A and it must be sure to not be remain B components inside container. During the application is needed, to mixture at a rate of 1/ 0, 3 by weight 0.1 to 0.3 mm can be used by adding quartz sand. Is poured onto the prepared substrate and spread with a notched trowel, or spreader (rubber or steel). Bubbles should be removed by rolling with a spiked roller.

Do not apply below 10° C. Relative humidity up to 75%, surface temperature, Dew point must be at least 3°C above. Applications is done in extreme cold conditions will negatively affect the film structure, such as will extend the duration of an erection. For optimum dissemination and ease application the surface temperature or materials temperature on 15°C as medium are recommended.

 

SPREADING RATE

1 mm thickness 1.7 kg / m²

 

REDUCTION

Do not reduce this product

 

DRYING TIMES (SINGLE COAT, STANDARD THICKNESS)

Re-coating time: Min 16 hrs – max. 3 days,  20°C in 48 hours can be opened to light traffic. 7 days for normal traffic should be expected.

 

MIXTURE LIFE

At 20°C, 30 minutes (The higher the temperature, the  shorter the life of mixture)             

  

CLEANING UP

Clean up with soap and water. After cleaning up be sure to flush spray equipment with solvent to prevent rusting following manufacturer’s instructions. Dispose of can in accordance with local authority guidelines.

 

PRECAUTIONS / WARNINGS

Keep out of reach of children. Ensure good ventilation during application and drying. If the product comes in contact with the eyes rinse immediately with plenty of water. To remove splashes from skin, use soap and water or a recognized skin cleaner. Do not take internally. If medical advice is needed, have product container or label at hand. Dispose of contents to a waste disposal facility in accordance with local/national regulations. Safety data sheet available on request.

 

STORAGE

The product should be kept in a dry place. Lid should be closed tight when not in use. Not to be exposed to direct sunlight.  Keep between 10-35 °C original package, approximately 1 year in unopened.

 

FOLLOW US ON

Online: www.southwindpaints.com

Email: info@southwindpaints.com

 

    Phone: +90 530 429 9233